How to Clean Motorcycle Engine

Motorcycles are a lot of fun until they break down. If you want to avoid this, it’s important to keep your bike clean and to run smoothly. The engine is one of the most important parts because that’s where the fuel goes in, and power comes out, so if anything gets clogged up or dirty, it could affect how your bike runs. That’s why you have to learn about how to clean motorcycle engine.

Cleaning a motorcycle engine may seem like a daunting task, but with the right tools and if you know how to clean motorcycle engine, it is quite simple. Cleaning your bike will not only allow you to enjoy riding on its clean surface but also keep your motorcycle running efficiently for years to come.

In this blog post, we’ll discuss how to clean your motorcycle engine so you can keep it running smoothly for many years to come.

Why You Should Wash Your Motorcycle Engine

Mud or dirt clogs an engine’s cooling system, which is cooled by air circulation in two-stroke and some four-stroke engines. When dirt, oil, and mud stick to the outside of the engine, it becomes difficult for air to cool the engine. The only remaining cooling element in these cases is lubricating oil, but it may not be sufficient.

Engines that are cooled by an antifreeze liquid have ducts between the radiator and the engine. This helps to make the liquid hotter so it can chill in the air.

In this case, dirt and mud don’t allow air to flow freely between the radiator channels, so the antifreeze liquid doesn’t cool down; therefore, the motorcycle’s engine remains hot.

The antifreeze hoses and lines of the motorcycle are exposed to dust. The dirt dries them out and can break them, leaving the motorcycle without a coolant system. It will need many repairs to fix.

So do I wash or not wash the engine?

Motorcycles that have sat for some time are even stuck and covered in dirt from previous years. Manually cleaning each piece of the head, carter, and others is the best approach. This is a good thing. This helps take off the oil and any residue. It reassembles and puts quality oil on it.

Motorcycle Engine Cleaning Materials

To clean your motorcycle engine, you’ll need to use the following materials:

  • Cover the electronic parts with plastic and adhesive tape
  • Several motorcycle shops carry degreasing liquids that you have to purchase.
  • Brush
  • Hose Pipe
  • A pressurized water system
  • A cloth to dry

Instructions to Clean the Engine of My Motorcycle

Cleaning a motorcycle engine can be difficult, but it is not impossible. You will need to get the right tools and supplies before you start working on this dirty job. To clean your bike’s engine properly, follow the steps below: 

Step-1

When you are cleaning an engine that has been used, make sure that it has cooled down before you start cleaning. There are many motorcycles with open-air motors, but there are also a lot of models that require you to remove the fairing. It is best to cover all electronic components with plastic after the motor has been exposed to the elements and has reached a low temperature.

Step-2

We will use adhesive tape to cover the electronic areas, and in this way we can start washing and the engine does not get wet. You must bear in mind that all the electronic parts have to be very well covered because if some water enters they can be damaged.

Step-3

The remaining parts of the engine can then be sprayed with a degreaser after the electronic parts are covered. We must let this product act for 5 minutes and then scrub the engine with the brush in the dirty areas. This product will remove all the grease from the engine.

Step-4

We will use water to rinse after we have cleaned all the dirt out of the engine. However, if our engine is still not completely cleaned, we can use pressurized water to finish the process.

Step-5

We have to cover electronic parts with plastics or adhesive tape and be careful not to make them wet. Otherwise, we may have to spend hours waiting for them to dry fully. If the engine electrical parts get wet, we can cause the motorcycle to fail, which would be extremely expensive.

Motorcycle Engine Cleaning Tips

It can be hard to figure out how to take care of your motorcycle. If you don’t know what tools should be used when washing and cleaning the engine, we are giving some tips below:

  • We must allow our motorcycle’s engine to dry after we have washed it completely. The process can be sped up by using a cloth and removing all the moisture in this way, but it is best not to use it again for several hours after removing the moisture.
  • Get as much knowledge about motorcycle maintenance as possible.
  • Maintain a clean motorcycle at all times. Therefore, it will have a longer useful life and a smoother ride. 

The importance of changing motorcycle oil

Also remember that a regular oil change is the best method for keeping the engine clean. The manufacturer will tell you how much oil to change in the service manual. The oil will remain as clean as possible without requiring the previous steps, and the detergents and dispersants contained in the oil will not run out.

FAQ

What can I use to clean my motorcycle engine?

Before cleaning the motorcycle engine, cover these sensitive areas with towels or plastic bags. Cleaner Aerosol or Gel will effectively break down grease and grime from even the stickiest surfaces. It uses modern detergent technology to cut through tough grease and grime effectively.

What is the best homemade degreaser?

Degreasing is simple with vinegar, liquid soap, baking soda, and essential oils. In addition to their effectiveness as sanitizers, liquid soaps have excellent degreasing and stain removal properties.

Should I pressure wash my motorcycle?

There will come a time when you have to wash your motorcycle, regardless of whether you ride a dirt bike or a street bike, and a pressure washer is a great way to effectively remove dirt, grime, and mud from your bike.

How do you deep clean a motorcycle?

Washing

  • Remove loose dirt by thoroughly rinsing your bike with cool water.
  • Use cool water and a sponge to clean it.
  • Cleaning the plastic uses a damp cloth or sponge dipped in a mild detergent solution. …
  • Make sure you thoroughly rinse the motorcycle after cleaning.

Conclusion

In this blog post, we discussed how to clean your motorcycle engine. We talked about the importance of cleaning oil and gas from an engine after use as these fluids attract dirt that will cause mechanical problems over time. It is always a good idea to have some paper towels or rags on hand for cleanup before you start up the motorcycle again so there are no surprises when it comes time to ride home!

Leave a Comment

  +  65  =  68